I've seen this technique a lot, but mostly as a post-processing technique where resin, fiber, or some other type of plastic is injected into the channels after printing is completed. It would be interesting to see this done during the normal printing process.
I am a little skeptical on the technique though. FDM printed walls are known to not handle pressure well, especially during printing when its past its glass-transition temperature. This process essentially uses the pressure from the extruder to inject a channel with molten plastic. Will this pressure could cause the walls to delaminate from each other or deform?
And how does this affect plastic that tends to warp significantly during printing? The molten plastic is injected into insulated channels that will not receive any active cooling. You're also parking the nozzle at the injection points, which will cause a lot of uneven cooling at the surface as well. For high-warping plastics like ABS, that could cause a lot of issues.
So I guess the underlying question should be, does this actually work? What is the measured difference in tension strength between parts printed normally vs with MAGMA infills? Specifically when using the same amount of plastic. There's no data or even pictures that indicate this is working.
I think the way this works is with an internal structure, that houses the plastic and is expected to deform, printed first (so it cools), then outer walls with perhaps some air gaping for insulation, then injection into the inner structure at the lowest temp possible, then the next level starts.
Would print slow but might be genuinely strong vs normal infill + many walls (weight for weight).
Multi head printers like the U1 or H2D could do even better with high temp plastics like carbon ASA or nylon for the inner structure and outer walls and strong but brittle PLA for the injection.
No, unfortunately. I've printed a ton of objects but nothing clean enough to be interesting.
The top of cells always melt as I'm using the same material for injection and the rest of the print. Someone with a dual nozzle printer could try something like PLA injection in a polycarbonate part. I added support but don't have a printer capable of that.
It's also possible that different print settings would work. I'm releasing the features to the community as I've run out of patience with doing a hundred hours of test prints.
We need to crowd test the best settings and nozzles, materials, etc to make this work well
I've seen this technique a lot, but mostly as a post-processing technique where resin, fiber, or some other type of plastic is injected into the channels after printing is completed. It would be interesting to see this done during the normal printing process.
I am a little skeptical on the technique though. FDM printed walls are known to not handle pressure well, especially during printing when its past its glass-transition temperature. This process essentially uses the pressure from the extruder to inject a channel with molten plastic. Will this pressure could cause the walls to delaminate from each other or deform?
And how does this affect plastic that tends to warp significantly during printing? The molten plastic is injected into insulated channels that will not receive any active cooling. You're also parking the nozzle at the injection points, which will cause a lot of uneven cooling at the surface as well. For high-warping plastics like ABS, that could cause a lot of issues.
So I guess the underlying question should be, does this actually work? What is the measured difference in tension strength between parts printed normally vs with MAGMA infills? Specifically when using the same amount of plastic. There's no data or even pictures that indicate this is working.
I think the way this works is with an internal structure, that houses the plastic and is expected to deform, printed first (so it cools), then outer walls with perhaps some air gaping for insulation, then injection into the inner structure at the lowest temp possible, then the next level starts.
Would print slow but might be genuinely strong vs normal infill + many walls (weight for weight).
Multi head printers like the U1 or H2D could do even better with high temp plastics like carbon ASA or nylon for the inner structure and outer walls and strong but brittle PLA for the injection.
When you say continuous interlocking U shape, are you saying it fills one channel from the top until the connected channel fills from the bottom?
Instead of one large channel throughout the whole print, why not multiple small 2-4 layer bridges?
Do you have a photos of objects you build with this? A video?
No, unfortunately. I've printed a ton of objects but nothing clean enough to be interesting.
The top of cells always melt as I'm using the same material for injection and the rest of the print. Someone with a dual nozzle printer could try something like PLA injection in a polycarbonate part. I added support but don't have a printer capable of that.
It's also possible that different print settings would work. I'm releasing the features to the community as I've run out of patience with doing a hundred hours of test prints.
We need to crowd test the best settings and nozzles, materials, etc to make this work well
Why do you think this is better than the old practice of filling straight holes a few layers deep?
Here for any questions about how it all works :).